No products in the cart.
Scaffolding
Sole boards
Soleboards are hardwood timber planks used under Scaffold base jacks to provide greater load bearing capacity.ÊFor uneven ground levels you can use the adjustbale base jacks
| Size | Weight | Painted | Galvanised | Item Description | Quantity | ||
|---|---|---|---|---|---|---|---|
| 0.5 M X 230 MM | 4.3 |  | 0.5 m sole board | ||||
| default variation | 4.3 | | 0.5 m sole board |
Solid base jack
Adjustable base jack enables accurate levelling of the scaffolding on uneven ground and infinite adjustment on sloping ground
| Size | Weight | Painted | Galvanised | Item Description | Quantity | ||
|---|---|---|---|---|---|---|---|
| 34 OD X 650 mm x 8 MM | 7.5 | | Solid base jack | ||||
| default variation | 7.5 | | Solid base jack |
Swivel base jack
Swivel Jack provides stability for uneven surfaces. The jacks has 180 degree rotation for extra flexibility. Made from heavy duty steel and galvanized to last longer.
| Size | Weight | Painted | Galvanised | Item Description | Quantity | ||
|---|---|---|---|---|---|---|---|
| 34 OD X 650 mm x 8 MM | 7 | | swivel solid base jack | ||||
| default variation | 7 | | swivel solid base jack |
Kwikstage Standards
Standards are vertical structural member of the scaffold system which are made from 48.3 OD X 4mm Tubes. Standards have ÒVÓ pressings in clusters at 495 mm centres, which provide location points for Transoms, Ledgers, Braces,, Hopups etc and a spigot fixed at the top
| Size | Weight | Painted | Galvanised | Item Description | Quantity | ||
|---|---|---|---|---|---|---|---|
| 0.3 M | 3 | | | Standard Topper | |||
| 0.5 M | 3.6 | | | 0.5 m standard | |||
| 1.0 M | 6.5 | | | 1.0 m standard | |||
| 1.5 M | 9.15 | | | 1.5 m standard | |||
| 2.0 M | 12.15 | | | 2.0 m standard | |||
| 2.5 M | 14.7 | | | 2.5 m standard | |||
| 3.0 M | 17.5 | | | 3.0 m standard |
Kwikstage Ledgers
Ledgers is horizontal member of the scaffold system also known as guard rails are made from 48.3 OD X 3.2 mm & 4 mm tubes. Ledgers fit into the upper ÒVÓ Pressings on the standards.
| Size | Weight | Painted | Galvanised | Item Description | Quantity | ||
|---|---|---|---|---|---|---|---|
| 0.7 M | 3.9 | | | 0.7 m ledger | |||
| 1.2 M | 5 | | | 1.2 m ledger | |||
| 1.8 M | 7.6 | | | 1.8 m ledger | |||
| 2.4 M | 9.3 | | | 2.4 m ledger |
Kwikstage Transoms
Transoms are made by welding two 5.00 mm angles back to back. Transoms fit into the lower ÒVÓ pressings on the standards to carry steel boards which make a safe working platform.
| Size | Weight | Painted | Galvanised | Item Description | Quantity | ||
|---|---|---|---|---|---|---|---|
| 0.5 M | 5.8 | | | 0.5 m transom | |||
| 0.7 M | 6.1 | | | 0.7 m transom | |||
| 1.0 M | 7.2 | | | 1.0 m transom | |||
| 1.2 M | 9.8 | | | 1.2 m transom | |||
| 1.8 M | 15 | | | 1.8 m transom | |||
| 2.4 M | 21 | | | 2.4 m transom |
Kwikstage Ledger Transoms
Heavy duty back to back angle transoms for location of scaffold boards. These are used to where greater loads are required for pedestrain access.
| Size | Weight | Painted | Galvanised | Item Description | Quantity | ||
|---|---|---|---|---|---|---|---|
| 1.2 M | 19 | | | 1.2 m ledger transom | |||
| 1.8 M | 32 | | | 1.8 m ledger transom | |||
| 2.4 M | 42 | | | 2.4 m ledger transom |
Kwikstage Hopup Bracket
Board Stage Brackets / hopups fit into the (V) pressing of the standard which is nearest to the wall. The 2 & 3 BSB have holes into which tie bar pins are attached. They are used to provide cantilevered platform on the inside of the scaffold nearest the wall.
| Size | Weight | Painted | Galvanised | Item Description | Quantity | ||
|---|---|---|---|---|---|---|---|
| 1 BOARD WIDE | 2.4 | | | 1 Board stage bracket | |||
| 2 BOARD WIDE | 6.5 | | | 2 Board stage bracket | |||
| 3 BOARD WIDE | 11.4 | | | 3 Board stage bracket |
Kwikstage Tie Bars
Tie bars have pins at each ends which fit in holes of 2 and 3 board stage brackets (hopups) to prevent the brackets from spreading and the planks from becoming dislodged
| Size | Weight | Painted | Galvanised | Item Description | Quantity | ||
|---|---|---|---|---|---|---|---|
| 0.7 M | 2.5 | | | 0.7 m tie bar | |||
| 1.2 M | 3.6 | | | 1.2 m tie bar | |||
| 1.8 M | 5.2 | | | 1.8 m tie bar | |||
| 2.4 M | 7 | | | 2.4 m tie bar |
End Toe Board Bracket
End Toe Board brackets also called toe board Clips are fabricated brackets placed on the outside of a scaffold standard to allow toe boards to be installed .
| Size | Weight | Painted | Galvanised | Item Description | Quantity | ||
|---|---|---|---|---|---|---|---|
| 0.3 M | 1 | | | end toe board bracket | |||
| default variation | 1 | | | end toe board bracket |
Toe board bracket
Toe baord brackets also known as toe board clips are Clamped to the standard with a captive wedge to hold the batten toe board vertically in place.
| Size | Weight | Painted | Galvanised | Item Description | Quantity | ||
|---|---|---|---|---|---|---|---|
| 0.3 M | 0.85 | | | Toe board bracket | |||
| default variation | 0.85 | | | Toe board bracket |
Double C Clips
Used to Join Kwikstage scaffolding Standards Back to Back for more stability and steenght to the scaffold structure
| Size | Weight | Painted | Galvanised | Item Description | Quantity | ||
|---|---|---|---|---|---|---|---|
| 0.3 M | 1.5 | | | Double C Coupler | |||
| default variation | 1.5 | | | Double C Coupler |
Showing 1–12 of 65 results